Task 9 Structure-based mutation analysis
- 1 Intro
- 2 Where to run the analyses
- 3 Preparation
- 4 Energy comparisons
- 5 foldX
- 6 Minimise
- 7 Gromacs (optional task for those who love MD!)
This time we make full use of the protein’s known crystal structures and try to predict energetic changes caused by mutations. We use different methods to generate structures and predict energies. For the analysis, we check how the predicted structures differ and how the predicted energy changes differ. Do any of the analyses lead to a plausible prediction of the effect of the mutation?
The slides to the talk can be found here: File:Structure based mutation analysis Karo.pdf
Where to run the analyses
- You have to use the student computer pool:
i12k-biolab0n.informatik.tu-muenchen.de, where n goes from 1 to 9 (or more?). The file server does not have blast etc. installed!
- The software and scripts to use can be found in the dir
Choose a structure to work with
Before we start you will have to choose one of structures available (if several can be used). In the previous sections you already had to use structures as references, so you could stick to your choice. However, in this part of the practical there are some additional constraints to observe.
- It is important that the structure has a high resolution (small Å value);
- furthermore the R-factor should be as small as possible, and the higher the coverage the better.
- Also, check at which pH-value the structure was resolved; ideally you want physiological pH (7.4).
- Finally, before you decide for a structure make sure it does not contain any gaps (missing residues) within the structure – this means two consecutive residues would not have a consecutive numbering.
- If there is no structure without missing residues, try to create a composite structure.
Visualise the mutations you want to work with
Map 5 mutations of your choice from the previously selected mutations onto the crystal structure:
- Color the mutants differently than the rest of the protein and create a snapshot for the wiki.
- If applicable find out whether the mutations are close to the active site, a binding interface or other important functional sites. Visualize this and describe it properly.
Create mutated structures
Next we use SCWRL to create our mutations. Make sure you only change one side chain for each mutated structure. It is possible to give SCWRL the mutated sequence. This can be done by extracting the sequence with repairPDB. Then you change all letters to lower case. Next you introduce the new amino acid letter (mutation) in capital letters to the sequence file. This sequence file can be read in by SCWRL using the –s flag. Check if only the mutated side chain has been changed.
In the following, compare wild type (WT) and mutant structures.
Investigate the local hydrogen-bonding network using pymol – also check for potential clashes (when sidechains are too close to each other). Are you introducing hydrophilics to the core or hydrophobics to the protein surface? Are there any holes introduced to the protein due to the mutations?
Now that you should have a clear idea of the WT and mutant proteins, we will try to calculate some energies. Always calculate the energy for the wild type and mutants – then substract/compare.
Use the following approaches:
before minimise and gromacs the hydrogens and waters (protein only) need to be removed using repairPDB
Examples how to use foldX can be found here: We want to use the approach Multiple mutations using indivudal list.
To run foldx you will need to make a static link in your working directory to the file
ln -sf /opt/SS12-Practical/foldx/rotabase.txt .
For each of the mutations also a new structure will be created. Note down all of the energies, but also use these structures in the next steps.
Compare the scwrl and foldx structures in Pymol and superimpose them. What are the differences?
In the next step you will use both the scwrl and the foldX structure as input to minimise.
Here we call minimise with the input structure filename as the first argument and the output filename as the second.
Apply this for all mutant structures (produced by scwrl and foldx) and the WT.
Also, use the output of one minimisation for another run as input. Do this 5 times for each structure. What happens regarding the energy? Please only look at the energy for the recursive runs. The structures should only compared for the second minimise run.
Gromacs (optional task for those who love MD!)
Gromacs is a powerful molecular dynamics package that can be used to simulate nearly any atomic system at different levels of accuracy. Here we will get a basic introduction. First we will get all the necessary files and then we will minimize our protein in vacuum. Finally we will analyze the energies during the minimization.
- For the mutations we will ONLY use the AMBER03 forcefield!
- For the mutation input choose either the scwrl or foldx structures. Base your decisions on the previous results and explain.
- Use repairPDB to clean the PDB and extract the protein only - describe what options you chose and what other options are available. Make sure you chose the right chain. Run SCWRL with the lowercase protein sequence to make sure there are no missing sidechains. The sequence can be extracted using repairPDB. After SCWRL you will have to remove the hydrogens again.
- Use the gromacs command “pdb2gmx” the option –f defines the input structure, -o the gromacs outputfile (.gro) and –p the topology (.top) output file. IMPORTANT the input must end with “pdb”. Choose a forcefield and for water the TIP3P model.
- Create a MDP file with the following content (for a description of the different keywords used in this file see the gromacs manual)
title = PBSA minimization in vacuum
cpp = /usr/bin/cpp
define = -DFLEXIBLE -DPOSRES
implicit_solvent = GBSA
integrator = steep
emtol = 1.0
nsteps = 500
nstenergy = 1
energygrps = System
ns_type = grid
coulombtype = cut-off
rcoulomb = 1.0
rvdw = 1.0
constraints = none
pbc = no
- Use grompp to prepare the system for gromacs (producing the file FILE.tpr, which we use in the next step):
grompp -v -f FILE.mdp -c FILE.gro -p FILE.top -o FILE.tpr
- Now we minimize the system:
mdrun -v -deffnm FILE
- Analyze the minimization of the system (Bond, Angle and Potential) with the following command:
g_energy -f FILE.edr -o energy_1.xvg.
The xvg graphs can be viewed with xmgrace and in the print settings you can choose eps output, then print and convert to pdf.
Further experiments (only for the WT!)
- Repeat step 3 to 6 with different settings for “nsteps” and measure the time of mdrun; create a plot nsteps versus time.
- Do the whole analysis for two other energy functions chosen in step 4 (AMBER03 should be included in any case).